You ne
ed to check ia Broadcasting Licence to opt in
The transmitter 1 watt for Low Power AM radio station
https://www.6v6.co.uk/transmitters/solid-state-transmitters/mosquito-am-one-watt-transmitter-us.html
Mosquito 1 Watt Plus AM Transmitter
The Mosquito 1 Watt AM Transmitter has been designed to cater for the new 1 Watt Low Power AM standards being introduced worldwide, (for example in Scandinavia and the Netherlands).
Using Class E technology, with extremely linear modulation characteristics, suited for high quality, amplitude modulation.
The output is protected from a short circuit to ground, and also has over current and thermal shutdown to protect the output stage if the antenna is badly tuned.
Specifications
- Frequency: 1000-1720kHz MW & 160M Band
- Power Output: 1 Watt Plus
- Output Protection: Short Circuit and Thermal
- Audio input: Mono or Stereo signal
- Audio connector: 3.5mm Jack Socket
- Antenna: 50 Ohm Impedance
- Antenna connector: RCA Phono or BNC
- Crystal controlled: 9KHz Channels for Europe (10KHz vesrsion available for the USA)
- Built in Antenna and Modulation monitor
- Power Input: 15 VDC at < 400mA (Regulated)
- Power connector: 2.1mm coaxial (tip positive)
- External Ground Connections
- Devices: 4 x IC, 2 x Transistor and 3 x MOSFET
The Mosquito transmitter is ready built and ready to run...at an affordable price...with the performance and features of units costing many times the price...!
The Mosquito employs a crystal controlled frequency synthesizer for accurate tuning and drift free frequency stability.
The Mosquito employs "Class E" output technology and provides the full 1 Watt carrier, the modulator stages includes both over current and thermal shutdown.
The Mosquito also has a two channel mixer for either Stereo to Mono or twin channel Mono audio sources.
The Mosquito printed circuit board uses a grounding technique that splits the RF and Audio grounds, as well as providing and external grounding point. In addition a new external "universal"power supply provides regulated DC power to the transmitter, supplied with county specific power leads for the EU.
- Fully Built and Tested: High Quality PCB, Plastic CASE to IP56
- AC Power Adapter: Power Supply 12-15V DC 90-240V AC 50-60 Hz
- Audio Cables included.
- Stereo 3.5mm jack to twin RCA (Phono)
Compliance
This product is available for shipping to
- The Netherlands: for use in the Netherlands for a “laagvermogen AM” (LPAM) license granted by Agentschap Telecom.
- Scandinavia: Sweden, Norway, Denmark & Findland
- Worldwide subject to any country specific regulations
- Exemple of antenna for low power AM radio station http://www.lpam.nl/antennes.html
EU R&TTE directive and EMC Directive 2004/108/EC - in order to purchase this item, you must agree that:-
1. For use in the Netherlands for a “laagvermogen AM” (LPAM) license granted by Agentschap Telecom.
or
2. The item will only be used within a completely RF screened and shielded metal enclosure or environment for testing, evaluation, experimental or laboratory purposes and any other use that does not radiate electro-magnetic waves into free space.
I am not an unqualified end user and I have RF engineering and electromagnetic compatibility skills at my disposal.
or
3. You intend to export the item to an address outside the European Union. Under no circumstances will this item be resold or put into service within the European Union.
or
4. For use by a Licensed Radio Amateur on 160M Band
Tornado HF200 Antenna
The Tornado HF200 Antenna is a long wire antenna incorporating a 9:1 UNUN at the feed point enabling it to be fed directly with 50 ohm coaxial cable.
It has been designed to complement the Tornado Transmitter operating on Medium Wave (1.2 Mhz to 1.7 MHz) just using the Tornado's Auto Tune feature.
At 50m in length (can be shortened) this antenna is capable of operating on all bands from 238m (1.2Mhz) upwards (an external ATU may be required on SW bands)
It may be mounted straight, as an inverted L or vee or sloper. It may also be bent or dog-legged to fit in available garden space.
Also the poly weave wire will not kink and is extremely strong.
Features
- Rugged design
- Easy setup
- Optermised for AM broadcast.
- Lightweight
- Manufactured in United Kingdom
Specifications
- End Fed Wire Antenna (configurable as)
- Random Wire
- Inverted L or V
- Sloper
- Frequency: 1.2 - 30 MHz
- Band: 238m upwards
- Power handling 50W AM, (400W, CW or SSB)
- Impedance 50 Ohms
- Connector SO-239
- Length 50 Meters (can be shortened, depending on application)
- Non-Kink Poly Weave Wire
- Made in Great Britain
- Earth stud M3
- UNUN Enclosure to IP66
Fully built and tested, and supplied with
- 9:1 UNUN
- Dogbone Antenna Insulator
Aucun commentaire:
Enregistrer un commentaire
Please indicate in your comment your amateur radio callsign, swl, or your email
Remarque : Seul un membre de ce blog est autorisé à enregistrer un commentaire.